What is a cleanout plug?

Beneath their drain covers is a plastic or metal cap, also known as a cleanout plug, as well as a standard drainage pipe. That cap stops waste water from flowing into the cleanout, forcing it to pass directly into the sewage pipe.

What size is the sewer cleanout plug?

4 inches
Cleanout plugs size 4 inches Threaded O-ring, stainless steel hardware.

How do you remove a sewer drain plug?

Driving a screwdriver at an angle into the outer edge of the cap. Then tapping it with a hammer to pry it open little by little. Directly tapping the fitting on top of the cap with small sledgehammer to get a little bit of movement. Again, if you accidentally break the cap, they are cheap to replace.

What is a sewer washout?

The sewer clean out is a pipe with a cap that provides access to the sewer line so that blockages can be removed. The lateral sewer line is the sewer line that connects your home to the public sewer system.

What does a cleanout plug look like?

A drain cleanout provides access to your main sewer line and is located outside of your home in the front or back yard. Cleanouts typically go unnoticed until there is a problem. They look like capped pipes sticking a few inches above the ground.

How do you unclog a sewer without a cleanout?

You may be able to clear a sewer clog by using a plunger.

1. Choose a toilet on the ground floor.
2. Tape over the tub, sink and shower drains with duct tape.
3. Get a bellows or force-ball plunger, insert it in the toilet bowl, let it fill with water and then plunge away.

Should a sewer cleanout have water in it?

It is one of the more common questions we do get asked, should my drains have water in them? And there are two answers: The first answer is YES: Your sewer drains should hold water in certain locations. The reason for the water in the drainage fixture is to prevent rodents and smells entering the building.

How do you remove a PVC drain cleanout plug?

Use an adjustable wrench or adjustable pliers to unscrew the clean-out plug from a P-trap. Place a bucket under the trap to catch the water that will spill out when you remove the plug. Turn the plug counterclockwise to remove it, install the replacement, and turn it clockwise to tighten it.

Can you put a 90 in a sewer line?

You should design your wastewater pipes in a similar manner, for the most part. It’s a bad plumbing practice to have a hard 90-degree bend in a horizontal drain line that’s buried in a slab or otherwise hidden. All drain lines should have a minimum fall of an eighth of an inch per foot of horizontal run.

How do you seal a cleanout plug?

Clean-out plugs usually can be sealed with plumber’s tape, or pipe thread tape, (commonly known as “Teflon tape,” although there’s no such product of that name) or with pipe dope, or pipe joint compound.

How do you unclog a 4 inch sewer line?

How to clear a main sewer line clog

1. Step 1: Loosen the cap on the drain pipe. Loosen the cap on the drain pipe.
2. Step 3: Feed the auger cable into the drain pipe.
3. Step 4: Run the auger until the clog is clear—and beyond.
4. Step 5: Hose down the pipe and auger cable.
5. Step 6: Slowly pull the auger back out of the pipe.

How do you clean out a sewer line?

How to clean out a main sewer line clog Step 1: Loosen the cap on the drain pipe Step 2: Open the cap and let the buildup drain out Step 3: Feed the auger cable into the drain pipe Step 4: Run the auger until the clog is clear—and beyond Step 5: Hose down the pipe and auger cable Step 6: Slowly pull the auger back out of the pipe

Where is my sewer line cleanout located?

One way to find it is to visualize a line from a floor drain running out toward the municipal sewer lines, which usually lie beneath the street. In most cases, the main clean-out will be located at some point along this line from floor drain to street. May 30 2019

How do you clean out plumbing drain?

There are several different ways you can clean your sink pipes, using common household items. For example, vinegar will clean your drain and pipes. Pour one cup of white vinegar down the drain, and then wait for about 30 minutes. Rinse with hot water. Baking soda and hot water also works well.

What is a cleanout in plumbing?

A cleanout is a component in plumbing that allows the plumber or someone accessing pipes to clear out any kind of blockage of debris which has accumulated in certain parts of the system. A cleanout is routinely placed at a connection point in sewer lines.